Each Fluke product is warranted to be free from defects in material and The A Manual Set provides complete information for operators and service or. Warning If the A Calibrator is operated in any way not specified by the A Operators Manual or other documentation provided by Fluke, protection. View and Download FLUKE A operator’s manual online. Multi-Product Calibrator. A Test Equipment pdf manual download.

Author: Fauzahn Muzilkree
Country: Singapore
Language: English (Spanish)
Genre: Software
Published (Last): 3 April 2007
Pages: 436
PDF File Size: 17.41 Mb
ePub File Size: 13.96 Mb
ISBN: 754-9-80213-852-5
Downloads: 37336
Price: Free* [*Free Regsitration Required]
Uploader: Mazurr

At the prompt, type the desired calibration command, e.

Applies to both simulated thermocouple output and thermocouple measurement. From 95 V to V, its output is a square wave-like signal that alternates between the negative peak and the positive peak, with the centerline at V. Frequency and phase calibration are recommended after instrument repair, and are available only by way of the remote interface IEEE or serial.

Then follow these steps to calibrate pulse width: They are not the calibration constants obtained when the A was calibrated by the factory before shipment.

Time Base Marker Calibration Procedure for an Oscilloscope This sample procedure uses the Time Marker function to check the horizontal deflection time base of your oscilloscope. The A Service Manual contains a table of minimum use specifications for performing full verification. Adjusting the Wave Peak Center with R omf.

For capacitance outputs, null out stray capacitance by connecting the test leads to the UUT, routing them but not connecting to the A Calibrator on a non- conductive surface.

Equipment Required for Calibration and Verification The equipment listed in Table is required to calibrate and verify performance of the A.

  CATHY MAXWELL THE PRICE OF INDISCRETION PDF

Verify the annunciator is on. The ESR is cleared set to 0 when the power is turned on, and every time it is read. Leveled Sine Wave Lrequency Verification. The 1 ps to 2 ns markers are generated from the leveled sine wave generator on the A50 board.

If you press ENTER without identifying the units for the entry, in most cases the A keeps the units that were last used.

You lose all calibration data permanently.

See SC Service information, Specifications, AC current non-sinewaveac current sinewavesAC current sinewaves extended bandwidth. Much of the SC can be calibrated interactively from the front panel.

TRIG If you are using the external trigger, use this key to toggle the trigger off and on. Leveled Sine Wave Flatness Calibration. Allow the power meter reading to stabilize. DACS are used to control the level of dc signals and to control the amplitude of ac signals. Program the Calibrator Mainframe to output the wave type and voltage listed in Table Page 19 RS Remote Connections The far right of the peak is fixed at the far right of the center line, as shown below.

Fluke 5500A/COIL Calculator User Manual

Table lists the interface messages that the calibrator sends. Required Equipment For Checking Calibration An overload condition is detected.

55000a the output of the A and establishes a new reference point for the error mode. Then follow these steps to calibrate the Wave Generator: After resetting the A, press to return to the Oscilloscope Calibration Option the Volt menu appears. Equipment Setup for High Frequency Flatness All high frequency flatness procedures use the following equipment: Rise Time Table The highest compliance voltage is limited to 2.

  HOW TO AVOID PROPERTY TAX CARL BAYLEY PDF

The factory default is 0. This User Manual contains information, warning, and cautions that must manuap followed to ensure safe operation and to maintain the instrument in a safe condition.

Manually lock the HP A to the range that gives the most resolution for the baseline measurements. All of the SC functions are listed in Tablewith the verification technique indicated. Front Panel Operation Setting the Output This feature is available only for single-output dc volts and dc current outputs. Temperature Calibration rtd Specifications 0.

Comments to this Manuals Your Name. The marker signal passing through the A50 board is connected up to the attenuator assembly. Adjusting the Aberrations for the Edge Lunction Edge Duty Cycle Verification. When one output is a harmonic of the other, the phase shift is based on the phase angle or power factor cosine of the harmonic signal.

Fluke a – Sc Multi-product Calibrator | eBay

Voltage HP 8A Settings. This is also true for several other commands and functions, as shown below, with their equivalent RS emulation. Remove the power rluke pushrod. The sinewave outputs are in rms, while the trianglewave, squarewave, and truncated sinewave outputs are in peak-to-peak. High End Resistance Connections with Equation.