IEC SOUND SYSTEM EQUIPMENT – PART 1: GENERAL. Buy IEC Ed. Sound system equipment. Part 1: General from SAI Global. Buy IEC SOUND SYSTEM EQUIPMENT – GENERAL from SAI Global.
|Published (Last):||7 November 2008|
|PDF File Size:||19.68 Mb|
|ePub File Size:||15.11 Mb|
|Price:||Free* [*Free Regsitration Required]|
All signals are 30s long, dBFS rmsstereo, 16bit and have Hz sample rate. Germain – What You Think About The standard itself is a lengthy document, 9 Sections and 3 Annexes covering 46 printed pages.
Calibrate the microphones per the instructions in the SoundCheck manual. The core of the method is testing with 602668-1 input signals and measuring level of their waveform degradation at the output.
Please download Chrome or Firefox or view our browser tips. This is an even-only harmonics companion of standard triangle signal.
This value is converted to dBV and used to calculate the IM and difference frequency stimulus levels. The content you have requested is available only 60268–1 registered visitors. A series of post processing steps calculates the attenuation curves, their average values and shows them on the final display. It can also be used to characterize the passive attenuation only of a standard non-ANC headphone.
Amendment 1 – Sound system equipment. Part 1: General
Please complete the short form below all fields are required. Accept and continue Learn more about the cookies we use and how to change your settings. Standard Number BS A special test signal “Program Simulation Noise”, whose spectral content is representative of music and speech.
Software Requirements SoundCheck No – I don’t want to receive the latest audio test information by email. Five separate sequences are provided, each designed to measure specific characteristics.
The following 35 tracks of various genres are used for objective measurements of audio equipment. Once calibrated, position the microphones 0. You may see iev of such measurements in the form of histogram on Portable players page. Noise speakers are set up adjacent to the HATS left and right ears.
Crosstalk and radiation curves are then shown on the final display. Relink dialog Here is a list of sequences and their default signal paths unique paths are in bold: Matthew Miller November 15, – 6: While test signals can be of any kind the measurement procedure stays the same and waveform degradation is measured with a single parameter – Difference level dB.
Along with listening tests SoundExpert performs objective measurements of audio devices and technologies. Take the smart route to manage medical device compliance.
Methods for specifying and measuring general characteristics used for equipment performance Status: Band-limited version of square wave is used.
It is generated by means of Fourier synthesis http: It is recommended that the sequences be run directly from the IEC folder. Calibrate the headphone amplifier channels per the instructions in the SoundCheck manual.
FebDecember 17, – 3: 6068-1 for specifying and measuring general characteristics used 602668-1 equipment performance. If the answer is No, the sequence jumps to post-processing steps which calculate passive attenuation and the final display step.
IEC-60268-7 Headphone Test Sequences
The play and record acquisition takes place 3 times and the user is prompted to reposition the DUT on the HATS in between acquisitions. Learn more about the cookies we use and how to change your settings. A series of post-processing steps follow to apply the weighting and correction curves, calculate the LAEQ and then the Simulated Program Characteristic Voltage is calculated along with the Hz voltage sensitivity.
Verfahren zur Festlegung und Messung von allgemeinen Kennwerten fuer die Geraeteleistung.
IEC Headphone Test Sequences – Listen, Inc.
It consists of two pure tones: The sequence then goes through a series of acquisition steps to generate four fundamental curves which are then post-processed to calculate crosstalk. In order to add these Signal Paths to your System Calibration or relink to existing Signal Paths, you should open each of the sequences individually and, if prompted, add or relink Paths to your System Calibration.
Registration required The content you have requested is available only to registered visitors. This sequence iiec the requirements of Section 8. Test signals Along with listening tests SoundExpert performs objective measurements of audio devices and technologies.
T he new audio metric allows to measure waveform degradation using music as a test signal. Hardware Requirements In order to run the sequences, the following hardware is required: It can be created by passing pink noise through a special filter irc defined in IEC 60268–1 Test Setup for measuring headphone voltage sensitivity. You may find similar items within these categories by selecting from the choices below:.
The sequence uses a stepped sine stimulus to measure frequency response, THD and impedance, a composite signal of 70 Hz and Hz with an amplitude ratio of 4: